Machinekit

Machinekit

GS2 VFD Driver

This is a userspace HAL program for the GS2 series of VFD’s at Automation Direct.

This component is loaded using the halcmd "loadusr" command:

loadusr -Wn spindle-vfd gs2_vfd -n spindle-vfd

The above command says: loadusr, wait for named to load, component gs2_vfd, named spindle-vfd

Command Line Options

  • '-b or --bits <n>' (default 8) Set number of data bits to <n>, where n must be from 5 to 8 inclusive

  • '-d or --device <path>' (default /dev/ttyS0) Set the name of the serial device node to use

  • '-g or --debug' Turn on debugging messages. This will also set the verbose flag. Debug mode will cause all modbus messages to be printed in hex on the terminal.

  • '-n or --name <string>' (default gs2_vfd) Set the name of the HAL module. The HAL comp name will be set to <string>, and all pin and parameter names will begin with <string>.

  • '-p or --parity {even,odd,none}' (default odd) Set serial parity to even, odd, or none.

  • '-r or --rate <n>' (default 38400) Set baud rate to <n>. It is an error if the rate is not one of the following: 110, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

  • '-s or --stopbits {1,2}' (default 1) Set serial stop bits to 1 or 2

  • '-t or --target <n>' (default 1) Set MODBUS target (slave) number. This must match the device number you set on the GS2.

  • '-v or --verbose' Turn on debug messages.

Note
That if there are serial configuration errors, turning on verbose may result in a flood of timeout errors.

Pins

Where <n> is gs2_vfd or the name given during loading with the -n option.

  • '<n>.DC-bus-volts' (float, out) The DC bus voltage of the VFD

  • '<n>.at-speed' (bit, out) when drive is at commanded speed

  • '<n>.err-reset' (bit, in) reset errors sent to VFD

  • '<n>.firmware-revision' (s32, out) from the VFD

  • '<n>.frequency-command' (float, out) from the VFD

  • '<n>.frequency-out' (float, out) from the VFD

  • '<n>.is-stopped' (bit, out) when the VFD reports 0 Hz output

  • '<n>.load-percentage' (float, out) from the VFD

  • '<n>.motor-RPM' (float, out) from the VFD

  • '<n>.output-current' (float, out) from the VFD

  • '<n>.output-voltage' (float, out) from the VFD

  • '<n>.power-factor' (float, out) from the VFD

  • '<n>.scale-frequency' (float, out) from the VFD

  • '<n>.speed-command' (float, in) speed sent to VFD in RPM It is an error to send a speed faster than the Motor Max RPM as set in the VFD

  • '<n>.spindle-fwd' (bit, in) 1 for FWD and 0 for REV sent to VFD

  • '<n>.spindle-rev' (bit, in) 1 for REV and 0 if off

  • '<n>.spindle-on' (bit, in) 1 for ON and 0 for OFF sent to VFD

  • '<n>.status-1' (s32, out) Drive Status of the VFD (see the GS2 manual)

  • '<n>.status-2' (s32, out) Drive Status of the VFD (see the GS2 manual)

Note
The status value is a sum of all the bits that are on. So a 163 which means the drive is in the run mode is the sum of 3 (run) + 32 (freq set by serial) + 128 (operation set by serial).

Parameters

Where <n> is gs2_vfd or the name given during loading with the -n option.

  • '<n>.error-count' (s32, RW)

  • '<n>.loop-time' (float, RW) how often the modbus is polled (default 0.1)

  • '<n>.nameplate-HZ' (float, RW) Nameplate Hz of motor (default 60)

  • '<n>.nameplate-RPM' (float, RW) Nameplate RPM of motor (default 1730)

  • '<n>.retval' (s32, RW) the return value of an error in HAL

  • '<n>.tolerance' (s32, RW) speed tolerance (default 0.01)

For an example of using this component to drive a spindle see the GS2 Spindle example.